John Deere Lawn Mower Tires

How To Remove A Flat Tire From A John Deere Mower

How to Remove Front and Rear Tires (Wheels) from John Deere X310 Lawn Mower Tractor
  • Step One: Lift the Mower on a Hydraulic Jack Be sure to place the jack on a strong part of the chassis.
  • Step Two: Remove the Axle Cap This is a soft rubber piece that protects the axles tip.
  • Step Three: Remove the Binder Clip There is a small clip that holds the washers in place. You can remove this with needlenose pliers.
  • Step Four: Remove the Washers There should be a couple of washers between the rim and the axle.
  • Step Five: Pull the Tire Off There are no bolts or other fasteners, so the wheel should come off easily.

What To Do If Your Lawnmower Tires Keep Going Flat

Machines are bound to develop technical or mechanical problems. And when it comes to your newly acquired Husqvarna, Toro, Honda, or John Deere riding/push mower, you should expect its components to wear and tear after some years. However, when problems like flat tires become frequent, they negatively affect your grass-cutting machines general efficiency. It goes that lawnmowers depend on tire pressure for maximum traction and performance. Thus, apart from the fact you will often replace mowing blades, belts, and filters, tires that keep going flat should be a real cause of worry.

So, What to do if your lawnmower tires keep going flat ?

If your lawnmower tires keep going flat it can be due to several reasons:

  • Rough lawn terrain
  • Insert tubes inside each tire on your mower
  • Buy quality and/or original tires

For an experienced handyperson or a homesteader, you will agree that fixing a flat tire on a lawnmower is not always easy. Sometimes, the damage is beyond repair, and the only option you have is to buy brand new tires. Thus, in answering the question of what to do if tires on your mower keep going flat, we would say there are many things you can do. First, one must delve into the real causes of flat tires before seeking a long-lasting solution.


  • 6 Final Remarks
  • How To Fix A Flat Tire On A John Deere Riding Mower

    Because you drive your John Deere lawnmower on rough surfaces, its tires can take a lot of wear and abuse. Over time, they may become flat for various reasons, which means you will have to fix them.

    To fix a flat tire on a John Deere riding mower, you will want to first identify the problem by taking the wheel off the axle and inspecting it. Depending on the issue, you may need to patch the tire, install an innertube, or replace the whole thing.

    Because each of these options requires multiple steps, were going to outline them in more detail.

    Also Check: How To Get Rid Of Raccoons In Backyard

    The Problem With Overinflating Tires

    While the psi labeling on tire sidewalls helps you monitor the pressure gauge, the temptation to overinflate is often real. We always think overinflating makes tires strong, sturdy, and handy. But there is a real danger that comes with it. First, it affects the braking threshold, especially in riding lawnmowers. Secondly, overinflating mower tires begets the risk of a blowout. It also speeds up tire wear and tear. With wear and tear, you should expect more problems, such as reduced traction.

    How To Change The Front Tire On A John Deere Lx165

    Marathon 15 x 6.00

    The John Deere LX165 is part of the 100 series of riding lawn mowers offered by John Deere to homeowners with medium- to large-sized lawns. A John Deere riding mower requires routine maintenance and repairs as the result of normal use. A damaged front tire can be part of this maintenance. Instead of taking the mower in for potentially expensive service, follow a few basic steps to change the front tire at home.

  • 1.

    Park the John Deere LX165 riding mower on a level area such as a driveway or other solid surface. Set the parking brake, leave the transmission in gear and turn off the ignition.

  • 2.

    Put on a pair of gloves to protect your hands while working. Place a jack under the front of the John Deere mower and raise the mower until the front tires are off the ground. Place a masonry block under the front of the mower and lower the mower onto the block for support while working.

  • 3.

    Remove the plastic cap from the hub on the wheel. Use a blade screwdriver to help pry the cap off the hub, if necessary, and set aside.

  • 4.

    Remove the snap ring from the end of the axle with a pair of snap-ring pliers. Remove the washer behind the snap ring and set both aside for later. Pull the wheel and tire from the axle.

  • 5.

    Obtain a suitable replacement wheel and tire or have the tire on the wheel repaired, based on personal preference. Slide the new or repaired wheel and tire back on the axle.

  • References

    Recommended Reading: How To Get Rid Of Moss On Lawn

    Tips And Tricks For Fixing A Flat Tire

    Here are some ways to ensure that your project runs smoothly.

    • Inspect All Tires If the source of the problem is wear and tear, chances are that other tires will be damaged as well. If youre going to fix one, you might as well patch or replace the others too.
    • Find the Best Method to Break the Bead While a screwdriver is a simple option, its not the only one. You can find out other ways to break the bead here.
    • Avoid Damaging the Rim If the rim gets bent, it can be difficult to repair. In some cases, you might have to replace the whole wheel.
    • Wear Gloves Gloves will not only keep your hands clean, but they can protect against potential hazards, such as gouging yourself with a screwdriver by accident.

    What Is The Rightlawnmower Tire Pressure

    First off, take note that tire pressure should not be too high or too low. Both extremes are always bound to cause problems. You should, therefore, inflate your lawnmower tires to optimal pressure . The big question is whether there is a standard pressure gauge for these machines or varies depending on the model. The good news is that like tires in bikes, airplanes and a car, determining the optimal tire pressure for your lawnmower is as easy as looking at the sidewall. You should spot a labeling Max.Press.XX where xx is the recommended psi. It could be 30, 34, or 40 psi, depending on the type of tires on your mower. For worn-out sidewalls, check the user manual for the optimal psi recommended by your lawnmower manufacturer. You can find tire pressure gauges here.

    Recommended Reading: How To Get Rid Of Flies In The Backyard

    Replacement John Deere Tires And Wheels

    John Deere Tires and Wheels

    21 Products Found

    • BOBCAT FastCat Pro and FastCat RZ zero-turn mowers
    • JACOBSEN HR5111
    • JOHN DEERE G100, L100, L105, L107, L110, L120, L130, D100, D110, D120, D140, D160, D170, Z225, Z245 and Z425
    • ARIENS Zoom 2050 and Zoom 2552XL
    • GRAVELY PM144Z, PM148Z, PM152Z, PM250Z, PM252Z, PM260Z, PM272Z, GE1748FL, GR1548FL, HE1748FL, HE1748FLP, HE1752FL, HE1548FLP, HE1952FL and HE1952FLP
    • JOHN DEERE 600, 700 and 800 series Z-TRAK mowers
    • CUB CADET 734-04039, 734-3058B, 753-04856A
    • GRAVELY 03471700, 03471700
    • HUSQVARNA 532133957, 5321339-57, 532 13 39-57
    • ARIENS 42″ EZR 1542, EZR 1742, EZR 1842, 48″ EZR 2048 and Zoom 1640
    • CUB CADET 38″, 40″ and 50″ decks
    • EXCEL 38″, 40″ and 50″ decks
    • JOHN DEERE 38″, 40″ and 50″ decks
    • MURRAY 38″, 40″ and 50″ decks, 2000 and older
    • SIMPLICITY 38″, 40″ and 50″ decks
    • TORO 13AP60RP744 and 14AP90RP744
    • JOHN DEERE AM116299, AM133602, M111489
    • JOHN DEERE 38″ and 48″ decks
    • JOHN DEERE 60″ and 72″ front cut and 50″, 60″ and 72″ standard cut decks
    • JOHN DEERE 50″, 60″ and 72″ front cut decks
    • JOHN DEERE 48″, 54″, 60″ and 72″ cut decks
    • JOHN DEERE 48″, 54″, and 60″ cut mid-size walk behinds and tractors 1600, 1600 Turbo and 1620 Front Mounts with 62″ deck
    • JOHN DEERE AM116299, M11489, M84690
    • MURRAY 092265, 092265MA, 092683, 092683MA, 92265, 92683
    • OD: 5″ x ID: 5/8″
    • Offset hub length: 1-3/4″
    • For 42″, 48″, and 72″ decks on L-100 , L110, L120, and G100 series tractors



    • JOHN DEERE 38″ and 48″ decks
    • and other models

    How To Replace A John Deer Lawnmower Tire

    Carlisle All Trail Tire Installation on a John Deere Lawn Tractor

    If a patch or innertube doesnt work, you will have to replace the whole thing. Since this wheel is tubeless, you can keep the original rim. Follow these steps to install a new tire.

    • Step One: Break the Bead You can use the method we mentioned in the previous section.
    • Step Two: Remove the Rubber It helps if you lubricate the beads before doing this.
    • Step Three: Place the New Tire on a Flat Surface Be sure to lubricate the new beads as well.
    • Step Four: Insert the Rim Start on one side and work your way around. Make sure that the rim is secure on both sides.
    • Step Five: Attach Ratchet Straps Wrap one or two around the tread. Doing this will prevent the tire from bowing out too much and detaching from the rim.
    • Step Six: Inflate the Tire Fill the rubber about halfway and then remove the straps. Then you can fill it the rest of the way.
    • Step Seven: Reattach the Tire Mount it to the axle, and you should be ready to go.

    Read Also: Deck Colors For White House

    How To Install An Innertube In A John Deere Tire

    Because these are tubeless tires, one way to extend their lifespan is to install an innertube. Doing this will allow you to drive on the wheel, even if there are cracks in the rubber. Be sure to select a tube size that fits your tire. If there isnt a precise match, opt for one that is a little smaller.

    How To Inspect A Tire For Damage

    Usually, the cause of a flat tire is a puncture. However, if your mower is old, the rubber could be cracked, leading to slow leaks. The first step is to fill the tire with air. Then, visually inspect the rubber for any damage. Be thorough, as there could be multiple leak points, not just one.

    If you cant spot any issues, the next step is to cover the tire with soapy water. Doing this will allow you to see where air bubbles are forming. Again, be thorough when doing your inspection, and check the sidewalls, the bead, and the tread.

    Depending on the extent of the damage, you have several options to fix the tire patch it, install an innertube, or replace it. Here is a breakdown of each method.

    Also Check: Home Depot Clearance Sale On Patio Furniture

    Sharp Objects Cause Tire Puncture

    Another known cause of flat tires in lawnmowers is the presence of sharp objects on the lawn. It could be broken glass, a nail, or a screw. The nature of a tire blowout should shed some light on the nature of the object. Most importantly, inspecting the tires could occasion a dreaded find such as broken glass pieces lodged in tire treads. While you can clear lawns before mowing so that they are free from stones, pebbles, and puncture-causing objects, smaller objects are often hard to spot.

    Time To Refill The Flat Tire

    John Deere Riding Lawn Mowers Front Tire Replacement

    Following the above steps to the letter should leave the patch tightly in place. Now, it is time to test the tire for puncture once again. You can also refill it with pressure while taking care not to exceed the max limit. If the patch does not let out air, roll down the jack and remove it. You are now ready to start mowing your lawn once again. Take note that fixing holes on lawnmower tires follows the same procedure as that of car tires. The only difference is that tires in mowers are narrower and smaller. Should you find the task challenging, we recommend seeking help from a specialist to avoid causing further damage to flat tires.

    Pumping your tire with a small air compressor is very convenient. You can find tire air compressors here.

    Don’t Miss: Tractor Supply Riding Lawn Mowers

    How To Change A Lawn Tractor Tire

    There are a few different times at which you may have to change a lawn tractor tire. This could include a popped tire, a worn tread, or just general wear and tear over time. Changing tires can help your tractor mow more evenly, while also providing better towing ability. It may seem hard to change a tire on a riding mower, but its actually not as difficult as it seems.

    Lets take a look at the steps it takes to change a lawn tractor tire.

    For more information regarding the John Deere lawn tractors or related products, contact your local John Deere dealer.

    Additional Resources:

    What Causes Flat Tires In Lawnmowers And How Do Deal With It

    Once in a while, the tires on your mower will go flat. However, it is something that does not always require a quick fix. Quick fixes would only escalate the problem to a point where punctures become frequent. Based on our experience with different types of lawnmowers, when tires go flat often, it signals a problem that could be deeply seated than imagined. It is always that time you dug deeper and unearthed the real cause of flattening tires on your mower. Do they have holes? Is it because of tread wear? Or could it be that tire sidewalls have cracks?

    The truth is that some tire problems are hard to determine unless you carry out an extensive diagnosis. It also means that the procedure for fixing flat lawnmower tires varies depending on the cause. But first, take note of the following causes of flat tires:

    Recommended Reading: Bioadvanced Fungus Control For Lawns

    Insert Tubes Inside Each Tire On Your Mower

    Tubeless tires have become popular, but they come with high maintenance costs. Tubes prevent air loss hence not having them inside tires means you have to be extra careful when mowing the grass. When tubeless tires hit a rut, there is a high risk of puncture. It is also noteworthy that tubeless tires tend to separate from the rim, hence more likely to go flat than the ones with tubes. You can find Lawn Mower tubes here.

    Tubes, apart from keeping tires airtight, also prolong their tire lifespan. For those who do not know how to fix tubes into tires, feel free to seek the services of a professional or a lawn mowing service provider near you.

    Buy Quality And/or Original Tires

    How to change a tire on a John Deere

    There is a real chance of buying counterfeit tires today. The risk gets more real for someone who has never considered replacing worn-out tires. So, you ask, whats the catch with tire replacement? Well, we advise that you purchase quality original lawnmower tires from a trusted dealer. There are more than a dozen manufacturers of tires who enjoy a good reputation worldwide. Original tires will not only last long but also last their value without going flat unnecessarily. You can find Lawn Mower tires here.

    Also Check: Kamigawa Neon Dynasty Commander Decks

    How To Patch A John Deere Tire

    If the leak is inside the tread, you can patch it. Because this wheel is tubeless, you can spray a tire sealant inside using the valve stem, following these steps.

    • Step One: Determine How Much Sealant to Use This product will tell you the proper amount based on the tires size. There should be a chart on the side of the bottle.
    • Step Two: Remove the Valve Stem Core There is a tool you can use to take this piece out. Make sure that it is at the five oclock position so that the sealant will go inside the wheel more easily.
    • Step Three: Attach the Sealant to the Valve There should be a tube that connects the nozzle to the stem.
    • Step Four: Inject the Sealant Squeeze the bottle until there is enough inside the tire. Wipe off any excess from the stem.
    • Step Five: Reinstall the Valve Stem Core Make sure that it is secure.
    • Step Six: Inflate the Tire Dont exceed the recommended maximum air pressure for the tire.
    • Step Seven: Drive the Mower You will need to drive for about five minutes to ensure that the sealant gets spread evenly throughout the tire.

    Maintenance Tips For Keeping Lawnmower Tires In Great Workingshape

    When usinglawnmowers, your safety should come first. While we will not look at dangersassociated with flat tires, you should ensure they have optimal pressure at alltimes. Ensuring the longevity of mower tires, therefore, means you do thefollowing:

    • Avoid sharp objects: Do not run over sharp objects such as nails, harpoons, rocks, cacti, porcupines, thorns, glasses, needles, and bolts. You should inspect your lawn for any of these before mowing.
    • Store the mower in shade: Construct a cool shed or a garage where you store your lawnmower when not in use. Dry rot on tires happens due to overexposure to direct sunlight. With dry rot, often manifest on the sidewalls, tires cannot contain pressure for a long lime. The risk of a blowout also becomes real.
    • Avoid chemicals while washing: When washing mower tires, do not use harsh chemicals. But if you do, rinse off with plenty of clean water.
    • Keep tire pressure optimal: Underinflated tires cannot support the weight of a mower hence risk getting damaged. On the other hand, overinflating tires puts them at risk of blowouts, something you dont want to experience when mowing uphill/downhill.

    Recommended Reading: Milwaukee Lawn Mower Release Date