Troy Bilt Riding Lawn Mower Troubleshooting

Problem #: Mower Cant Drive Correctly

Troy-Bilt Pony 42inch deck riding lawn mower Full repair guide.

Another troy-bilt zero turn mower problems is having trouble driving in a straight line or turning, there could be an issue with the wheels. The wheel alignment might be off, or the tires might be inflated to the incorrect pressure.

How to Fix It:

The first thing you should do is check the tire pressure. If the tires are inflated to the incorrect pressure, they will cause the mower to drive erratically.

Next, check the wheel alignment. If the wheels are not aligned properly, they will also cause the mower to drive erratically.

Finally, if the problem persists, take the mower to a qualified technician for diagnosis and repair.

Problem #: Mower Stops While Mowing

When the mower is running, theres no problem. But if it suddenly stops while youre mowing, there could be several reasons.

An overheated engine might cause your Troy Bilt mower to quit while youre in the middle of it. lawnMowers can also stop if theres a problem with the carburetor, fuel tank, or air filter. This is general troy bilt riding mower transmission problems.

How A Riding Lawn Mower Is Powered

Riding mower is powered by a four-cycle engine . Some mowers use gasoline as their fuel and a spark plug to combust it. Others are powered by diesel and require no spark plug. In either case, the engine runs the transmission and drive wheels, and rotates the cutting blades underneath the machine.

Like automobile car, riding mower requires to charge a battery, starter motor, and ignition switch. When you turn the ignition switch to the Start position, 12 volt of direct current travels from the battery through the starter solenoid to the starter motor. This current also flows through a cable to the anti-afterfire solenoid in the engine

When you release the key to the Run position, this DC of twelve volts is then redirected. Instead of going to the starter and motor, it moves to the alternator and anti-afterfire solenoid only. Together, these parts help to charge the battery and start auxiliary power sources like headlights and power plugs.

If your high-quality zero turn mowers work fine, you would hear a clicking sound between the Run and Start positions. This implies that the starter solenoid is getting power from the battery. On the other hand, when you dont hear a click from the engine, the starter has failed, or its coil isnt getting power from the battery.

Although mowers differ from models, they all work on the same principles.

Don’t Miss: Forest Lawn Hollywood Hills Plots For Sale

Problem #: Gas Leaking

ProblemIf you notice gas leaking from your Troy Bilt zero-turn mower, the problem could be with the fuel line. This is a common issue and is usually caused by a crack or hole in the fuel line.

How to Fix It:

Our professional landscapers recommend replacing the fuel line if you notice any gas leaking. If the issue is with the fuel tank, you may need to replace the entire tank.

Check And Charge/replace Dead Battery

Best rear engine riding mower: Complete buying guide

Battery troubles are one of the most common reasons a mower wont run or click. A corroded battery wont start an engine, and neither will a drained battery, when you forget to turn off the safety switch. Corrosion can be a usual problem for used riding lawn mower models at cheap prices of $500 below, so make sure to check this when you buy one.

A service monitor on a mower can help you identify when youve got battery troubles. But without one, you can check the battery using a multi-meter by following these steps:

  • Turn off the ignition system before accessing the battery.
  • Set the multimeter to DC voltage
  • Use the multi-meter’s red probe to touch the positive terminal and the black probe on the negative terminal.

If the multitester reads more than twelve volts, the battery is good. Otherwise, it is weak, or dead and youve found the problem with your mower.

  • Accessing the battery, which is usually under the driver’s seat.
  • Connecting the charger clips to the battery terminals.
  • Plugging the charger to a power outlet. The charger should work on at least 10volts to charge the battery. Still, a 12-volt charger is sometimes preferred.
  • Disconnecting the charger reversing the steps above.
  • Plugging the charger to a power outlet. The charger should work on at least 10volts to charge the battery. Still, a 12-volt charger is sometimes preferred.
  • Replacing the seat and reconnecting the new battery in your mower correctly.

You May Like: Patio Furniture For Small Spaces

Problem #: Mower Wont Start

If your Troy Bilt mower wont start, there are a few possible culprits.

One of the most common reasons is that the mower is not getting enough electrical current.

This could be due to a problem with the ignition switch, the battery, or another electrical system component.

Another common reason for a mower not starting is an airflow obstruction. This could be caused by a clogged air filter or a blockage in the exhaust system.

Finally, if your mower has a gas engine, ensure enough fuel is in the tank. If the tank is empty, the mower will not start.

How to Fix It.

  • Check out the gas tank and fill it up if its empty.
  • If your mower has an electric starter, ensure the battery is fully charged.
  • If your mower has a pull starter, check to see if the cord is stuck or damaged.
  • Finally, if you suspect an electrical problem, take the mower to a qualified technician for diagnosis and repair.

Problem #: Troy Bilt Riding Mower Transmission Problems:

You may experience some common troy bilt zero turn hydrostatic transmission problems while mowing. These include leaking fluid, difficulty moving the mower, and the mower stopping unexpectedly.

How to Fix Troy bilt hydrostatic transmission problems:

If your mower is leaking fluid, its probably due to a seal or gasket that needs to be replaced. If the mower is having trouble moving, make sure that the transmission fluid is at the correct level.

If the fluid is low, add more until it reaches the full line on the dipstick. Finally, if the mower stops unexpectedly, check the brake pads and replace them if they are worn.

Don’t Miss: Patio Set With Fire Pit

The Spark System Test

If you have identified a likely spark system fault, then lets test all the components of the system, beginning with the most common failures plug coil control module ignition switch.

Have a new plug on hand, a helper, insulated pliers, and a plug removal tool. These tests are simple, however, take care to ground the plug against the engine securely, as a bad ground will lead to an incorrect diagnosis.

Good ground

Alternatively, make life easy for yourself and buy the Ignition spark tester, youll find the type I use here on the Small engine tools page.

For this test, you will need a new plug, plug spanner, insulated pliers, and a helper.

Note: The best way to test spark is with a spark tester tool, as it will load up and stress tests the coil.

Remove the spark plug and check the condition. Refit the plug wire and ground the plug on the engine.

Have a helper turn the key while you check for spark. Now try a new spark plug.

How To Clean A Troy Bilt Lawnmower Carburetor Step By Step

Troy Bilt Pony riding mower not starting- the problem, the fix and servicing the mower

Youre fully ready for a regular mowing session for your garden. But when you start your trusty Troy Bilt lawnmower, you notice that it is malfunctioning. The engine does not start or does not produce enough power. One of the most common causes of problems with the engine is a faulty carburetor that may need to be serviced. This blog will give you all the details to fix this problem for both beginners and more experienced users.

How to clean a Troy Bilt riding a lawn carburetor, step by step:

  • Step 1: Detach the battery cables and remove the air filter assembly under the hood to reach the carburetor.
  • Step 2: Disconnect the fuel lines and loosen the studs to remove the carburetor.
  • Step 3: Service the carburetor jets, bowls and float with a carb cleaner spray.
  • Step 4: Reinstall the carburetor and inspect the engine for performance.

Carburetors are engine parts that combine air and fuel to supply it to the engine for combustion. Due to poor fuel consistency and seldom cleaning, carburetor jets are blocked by debris and fuel deposits. As a result, the engine has degraded performance. In riding lawnmowers, maintenance is a little difficult due to the presence of more parts/components.

Please keep reading the article for a step-by-step method to remove and clean a Troy Bilt lawn mower carburetor in more detail.


Read Also: Wonder Of The Seas Deck Plans

How To Fix It Yourself Fast

Regular lawn mower maintenance helps prevent problems, plus lengthens the life of your lawn equipment. But even with plenty of TLC, normal wear and tear from hours of mowing the lawn increases the chances of hitting a glitch from time to time.

Warning:Always refer to the operator’s manual before starting any maintenance project on your equipment.

Common Troy Bilt Lawn Mower Problems + Troubleshooting Solution

If youre the proud owner of a Troy Bilt zero-turn mower, then you know just how great they can be for getting the job done quickly and easily.

However, even the best machines sometimes experience problems. In this article, well look at some of the most common Troy Bilt zero turn mower problems, as well as provide troubleshooting solutions to help you get your machine back up and running in no time.

Common troy bilt zero turn problems can be associated with a spark plug, blades, fluid, air, oil filter, and transmission problems. Lets have a look at the following points:

Recommended Reading: Michael Jordan Upper Deck Basketball Card

Where Is The Carburetor Located On A Troy Bilt Lawnmower

The carburetor is mounted just below the hood under the engine blower assembly on a riding lawnmower. You need to remove the hood first. To reach the engine, you need to take off the air filter assembly and the engine blower cover. The carburetor is attached in front of the engine. It is mounted on the engine with the help of its studs and has the fuel lines and the air intake attached to it.

How To Fix A Flooded Troy


Troy-Bilt riding lawn mowers such as the Pony model have carburetors that can become flooded with gasoline when starting. A flooded riding mower will typically not start, and basic troubleshooting is necessary to return the mower to normal operation. In most cases, you can correct the problem without the need for professional servicing.

  • 1.

    Locate the throttle lever on the dash of the Troy-Bilt riding mower. Move the throttle up to the “Fast” position. Make sure the power take off or blade engagement is in the “Off” position and set the parking brake.

  • 2.

    Turn the ignition key clockwise or to the right until you feel resistance and attempt to start the mower. Repeat the process to attempt to start the mower if it does not start the first time. Do not hold the ignition in the start position for more than 10 seconds to prevent damage to the starter.

  • 3.

    Move the throttle control to the “Slow” setting and let the mower set for 15 minutes to allow gas in the carburetor to evaporate, if the mower will not start.

  • 4.

    Return to the mower, move the throttle to the “Fast” setting and turn the key to start the mower. Move the throttle to the desired throttle setting once the mower starts.

  • References

    Don’t Miss: Backyards With Above Ground Pools

    Electric Start Wont Start Just Clicking

    I have a brand new mower. Charged it for 10 hours it wont start just clicking!

    Does the mower start when you pull the rope? If so, then your electric starter is bad. You need to take it back to the store for repair or replacement.

    Even if the mower won’t start when you pull the rope, since the mower is brand new, take it back to the store for repair or replacement.

    Was this answer helpful?

    I have the same issue, except I’ve had it for a couple of years. Mine recently started misbehaving and not shutting off when blade control handle was let go, and took me pushing the little metal switch thingy on the mower in. I recently fixed that, and electric start worked for a bit, and then suddenly it wouldn’t start anymore. So I bought a new off brand mower only to have it suddenly start running slow, and it’s self propel quit working. It of course has an engine that needs primed . Then I managed to fix the mower after discovering the ground wire was half broken, so I redid the ground wire And replaced the cover and lo and behold it started but then later on electric start stopped working at some point. It still starts with the the pull cord, but also it will sometimes spit black exhaust out when starting. Not a lot, but once it gets up to speed meaning the engine, no color to exhaust which is good. But when you shut it off it smells strongly of fuel. I’ve done carb cleaner and fuel treatment and it runs better, but still does the black exhaust.

    Was this answer helpful?

    Step 2 Remove The Carburetor From The Mower:

    In Troy Bilt riding mowers, taking off the carburetor is less easy than in a Troy Bilt walk-behind mower. For the disassembly, the following steps have been mentioned:

    Step 1. Detach the cables of the battery:

    Remove the key if it is in the ignition switch. Before removing the carburetor, you first need to make sure that the battery is not attached, which could cause the Troy Bilt mower to start. To do this, you can raise the mower seat under which the battery is placed and disconnect one of its terminals.

    -Step 2. Remove the housing of the engine blower:

    You need to remove the mower hood to reach the carburetor. The following sections shall be located under the hood, which needs to be removed.

    • Air duct: Just under the hood, the air duct directs the air to the air filter. Remove the air duct screws and remove the duct from the mower.
    • Air filter assembly: The whole air filter assembly that consists of the air filter cover, the air filter housing, and the filter needs to be removed. First, take off the air filter cover, then the air filter, and finally the air filter housing by loosening the screws.
    • Blower housing: Blower housing is another component that needs to be removed. You should loosen the screws on the front and back of it to make sure it stays off.

    -Step 3. Detach the lines of air and fuel:

    -Step 4. Remove the carburetor:

    You May Like: Backyard Discovery Skyfort Ii Swing Set

    What To Do When Your Engine Turns Over But Wont Start

    Inspect the engine throttle choke and control to make sure it is positioned correctly.

    Make sure you have gasoline in your tank also check to make sure the fuel line and fuel filter arent clogged with dirt or debris. If youre unsure, replace your fuel filter.

    Look to make sure the spark plug wire hasnt disconnected replace the spark plug with another one.

    Step 3 Clean The Carburetor:

    Problems with Troy Bilt Pony Riding Lawn Mower

    The carburetor removed is now to be serviced. You should follow the steps mentioned:

    Step 1. Carry out external cleaning:

    Externally, you could see the carburetor jets along with the throttle shaft. Use a carburetor cleaner spray on the throttle shaft and the visible jets from the outside to clean them. Make sure the black residues are removed and the shaft rotates freely. Clear any deposits you see on the outside by spraying the cleaner continuously.

    -Step 2. Clean the main jet:

    Remove the bowl nut under the carburetor. The nut is the main jet that supports the bowl, which extracts fuel and has the greatest risk of being congested. Using a thin metal wire, clear these deposits and ensure that the jet is cleared from any debris. Also, spray the jet with a little carb cleaner.

    When you see the mist of the cleaner coming out of the other end, you know its unblocked. Normally, the bowl is quite dirty with debris, rust, and deposits. Spray the cleaner on the bowl as well.

    Step 3. Clean the needle and the float:

    After the bowl has been removed, the needle and float are visible. The float regulates the volume of fuel with the help of the needle.

    Spray the cleaner onto the float pin that may be sticky with the clogs and the needle. Make sure it is clean and the deposits have been dislodged.

    After cleaning, reassemble the carburetor components such as the float, needle, bowl, and bowl nut.

    Recommended Reading: Aluminum Patio Covers Do It Yourself

    What To Do If The Mower Engine Turns Over But Doesnt Start

    So, lets say you have done your troubleshooting above and the engine turns over, yet wont start. There is further troubleshooting to be done to help find and solve the issue. Follow the first step above and ensure that the parking brake is on and the cut deck is engaged. Then, you are ready to move on to the next step.

  • Engine throttle choke. Start by inspecting the engine throttle choke and control. Sometimes it can get lodged out of position and prevent the engine from starting. Make sure that it is positioned properly before moving on to the next step.
  • Do you have gas? There is a saying that the simplest explanation is usually the right one. It happens more often than you would think but running out of gas is a very real possibility. Check to ensure that you have gas in the tank and fill it up if you do not.
  • Check the fuel line and filter. While you are checking to see if you have gas, check the fuel line and filter. Sometimes, either or both can get clogged up with debris, dust, and dirt. If you arent 100% certain, consider replacing the fuel filter just to be safe.
  • Spark plug. There are times where the spark plug can be disconnected or failing, not delivering the necessary spark needed to get the engine going. Verify that the spark plug is connected. You may want to consider replacing it anyway this is a relatively cheap fix.